自掺杂SnO2微球的水热合成及其可见光催化性能

本研究采用水热法,以柠檬酸为螯合剂,通过控制n(Sn⁴⁺)/n(Sn²⁺)的数值,合成了由具有丰富氧空位的SnO₂纳米晶体组装成的微球。通过X射线衍射(XRD)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)、傅里叶红外光谱(FT-IR)、X射线光电子能谱(XPS)及UV-Vis漫反射光谱对SnO₂纳米微球进行表征分析,结果表明:在酸性水热条件和柠檬酸的螯合作用下,二氧化锡纳米晶体聚集形成微球;在Sn⁴⁺/Sn²⁺摩尔比例为3:7时,其微球尺寸最小,整体分散性较好;同时适量二价锡离子的掺杂使得该样品氧空位浓度达到最佳,氧空位的存在将使得样品光吸收范围拓展至可见光,因而该样品显示出较强的可见光催化效率,在8 min内完全降解甲基橙。     

A Category of Restricted Modules for the Ovisenko-Roger Algebra

In this paper, we study a category of restricted modules for the Ovsienko-Roger algebra, which is an extension of the Virasoro algebra of its tensor density module of degree one. We construct and characterize simple modules in this category and give natural free field realizations of certain restricted modules using the Weyl vertex algebra.

     

基于抛光基材的热蒸镀铜箔生长高平整单层石墨烯薄膜

在石墨烯的化学气相沉积工艺中,铜箔是决定石墨烯薄膜质量的重要因素。传统铜箔由于制备工艺的限制,存在大量的缺陷,导致石墨烯薄膜的成核密度较高。本工作选用抛光铝板、抛光不锈钢板、微晶玻璃和SiO₂/Si作为基材,用热蒸镀法制备了不同粗糙度的铜箔,并详细讨论了以该系列铜箔生长高平整度石墨烯薄膜的条件及铜箔对石墨烯薄膜品质的影响。实验结果表明,铜箔以(111)取向为主,与基材分离后,表面具有纳米级平整度。在生长石墨烯后,从SiO₂/Si剥离的铜箔成核密度是4种基材中最小的。同时,从SiO₂/Si剥离的铜箔晶体结构变化最不明显,具有良好的结晶性,表面几乎不存在铜晶界缺陷。当压强为3 000 Pa,氢气和甲烷流速分别为300 mL/min和0.5 mL/min时,可以获得约1 mm横向尺寸的石墨烯单晶晶畴。     

吉林大学物理化学学科:笃学致远 润物无声

伴随建系而生的吉林大学物理化学学科是吉大化学学科的重要组成部分,在70年的发展中为整个化学学科的发展建设做出了重要贡献。吉大物化人一直坚持理论与实践并重的教育思想,培养了大批优秀人才。回顾了吉大物理化学学科的历史沿革,展现了吉林大学化学学院物理化学在课程和教材建设、科学研究和人才培养等方面所取得的成绩。在吉大化学70周年华诞之际,谨以此文向为吉大物化学科建设做出贡献的前辈致敬。     

LaNi0.5Co0.5O3催化剂对甲烷二氧化碳干重整反应在CO2渗透膜反应器中的影响

制备了混合导体膜反应器,通过电化学方法捕获CO2,并将其用于甲烷二氧化碳干重整反应中.采用XRD, SEM,TPR等技术系统研究了LaNi0.5Co0.5O3催化剂在膜反应器中对甲烷二氧化碳干重整反应的影响.结果表明:LaNi0.5Co0.5O3催化剂在甲烷干重整反应中能原位析出纳米金属Ni和Co,对反应起到了较好的催化作用,同时抑制了积碳.催化剂还具有良好的氧化还原性能,可以循环利用.     

无需热处理高炉渣微晶玻璃的制备与表征

采用熔融法熔制具有金色星点的微晶玻璃,制备过程无需热处理.利用DSC-TG、XRD、SEM、EDS、TEM、BSE、FTIR和热膨胀研究该微晶玻璃配合料的高温熔制过程和不同熔制温度、保温时间对微晶玻璃晶体含量、显微结构和性能的影响.研究表明:配合料在850℃生成钙铝黄长石晶体并在1010℃逐渐转变为辉石,配合料在1200℃时大量熔化,仅含有熔点较高的正方铬铁矿石,随着温度的升高,正方铬铁矿溶解,玻璃液中析出绿铬石晶体;晶体含量随着熔制温度的升高而减少,随着保温时间的延长而增加.     

Limit cycle bifurcations near a double homoclinic loop with a nilpotent saddle of order m

In this paper, we study the explicit expansion of the first order Melnikov function near a double homoclinic loop passing through a nilpotent saddle of order m in a near-Hamiltonian system. For any positive integer $m(m\ge 1)$, we derive the formulas of the coefficients in the expansion, which can be used to study the limit cycle bifurcations for near-Hamiltonian systems. In particular, for $m=2$, we use the coefficients to consider the limit cycle bifurcations of general near-Hamiltonian systems and give the existence conditions for 10, 11, 13, 15 and 16 (11, 13 and 16, respectively) limit cycles in the case that the homoclinic loop is of cuspidal type (smooth type, respectively) and their distributions. As an application, we consider a near-Hamiltonian system with a nilpotent saddle of order 2 and obtain the lower bounds of the maximal number of limit cycles.     

Polymer nanoparticles with a sensitive CO2‐responsive hydrophilic/hydrophobic surface

Poly(methyl methacrylate) (PMMA) nanoparticles with a sensitive CO₂‐responsive hydrophilic/hydrophobic surface that confers controlled dispersion and aggregation in water were prepared by emulsion polymerization at 50 °C under CO₂ bubbling using amphiphilic diblock copolymers of 2‐dimethylaminoethyl methacrylate (DMAEMA) and N‐isopropyl acrylamide (NIPAAm) as an emulsifier. The amphiphilicity of the hydrophobic–hydrophilic diblock copolymer at 50 °C was triggered by CO₂ bubbling in water and enabled the copolymer to serve as an emulsifier. The resulting PMMA nanoparticles were spherical, approximately 100 nm in diameter and exhibited sensitive CO₂/N₂‐responsive dispersion/aggregation in water. Using copolymers with a longer PNIPAAm block length as an emulsifier resulted in smaller particles. A higher concentration of copolymer emulsifier led to particles with a stickier surface. Given its simple preparation and reversible CO₂‐triggered amphiphilic behavior, this newly developed block copolymer emulsifier offers a highly efficient route toward the fabrication of sensitive CO₂‐stimuli responsive polymeric nanoparticle dispersions. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019, 57, 2149–2156     

Enhanced CO2 Electrolysis with Metal-oxide Interface Structures

The ever-decreasing fossil fuels and the increasing greenhouse effect have caused substantial concern.Solid oxide electrolyser cell(SOEC)with La_0.75Sr_0.25Cr_(0.5 )Mn_0.5O_3-δ(LSCM)as a cathode was used for CO₂ electrolysis to CO.In this work,the metal-oxide interface was constructed on the LSCM framework by in-situ exsolution and impregnation,and the uniform distribution of metal nanoparticles on the LSCM framework was confirmed by spectroscopy techniques and electron microscopy techniques.The existence of three-phase boundary promoted the absorption and electrolysis of CO₂.(La_0.75 Sr_0.25)0.9(Cr_(0.5 )Mn_0.5)_0.9(Ni_0.5 Cu_0.5)_0.1 O_3-δ(LSCMNC)showed the best electrolytic CO₂ performance at 850℃and exhibited excellent electrocatalytic activity after 100 hours of long-term testing and 8 redox cycles.     

原位合成Bi3O4Br/Bi12O17Br2光催化剂及其对磺胺甲噁唑降解性能

Bi_xO_yBr_z光催化剂在有机药物废水处理领域有着非常广阔的潜在应用价值,但因光生电子和空穴的快速复合而表现出较低的光催化效率,进而限制了其应用范围。通过简易的水解-焙烧法原位制得一种新型的Bi₃O₄Br/Bi₁₂O₁₇Br₂复合光催化剂,并以磺胺甲噁唑(SMX)为模拟药物污染物进行了光催化性能测试,对所制催化剂进行了X射线衍射(XRD)、X射线光电子能谱(XPS)、扫描电子显微镜(SEM)、紫外可见漫反射光谱(UV-Vis DRS)、电化学阻抗(EIS)、光致发光光谱(PL)等表征。结果表明所制备的Bi₃O₄Br/Bi₁₂O₁₇Br₂复合光催化剂具有较强的光生载流子分离率、较低的界面电荷转移电阻,进而展示出优异的光催化降解SMX性能,在模拟太阳光下照射30 min,SMX降解率达到87%,相较于纯的Bi₃O₄Br和Bi₁₂O₁₇Br₂催化剂,降解率分别提升了30%和24%。最后基于自由基捕获实验和催化剂能带结构分析了所制催化剂的降解机理。